Skip to content
Frenchman's Bay Garage Door ServicesRequest a visit
Open 24/7(289) 301-8323Call now
Technician in an olive cap pointing a yellow-handled screwdriver at the wiring of a ceiling opener above a windowed door.
Open 24/7 in Toronto

Garage Doors in Toronto, OntarioCold snap.Stiff door.

Call now · open 24/7(289) 301-8323

What's happening right now?

Door stuck open

Safely, right now

  1. Leave it where it stopped. Don't pull it down by hand or keep pressing the button.
  2. Keep the doorway clear of people, pets and vehicles.
  3. Don't pull the red release cord while the door is open. It can drop.
Call (289) 301-8323

Request a visit What the fix involves

Door won't close

Safely, right now

  1. Don't keep hitting the button. Repeated tries can do more damage than the first fault.
  2. Don't step or reach under the door to move anything. If a bin, bike or snow is in the way, mention it when you call.
  3. Leave the safety sensors near the floor as they are: never tape them or bypass them.
Call (289) 301-8323

Request a visit What the fix involves

Spring snapped

Safely, right now

  1. Leave the door and the opener alone: no lifting it by hand, no pressing the button.
  2. Nobody and nothing goes near the door: people, pets and cars stay clear.
  3. Don't pull the emergency release while the door is open. It can drop.
Call (289) 301-8323

Request a visit What the fix involves

Car stuck inside

Safely, right now

  1. Don't drive into the door or try to force it open.
  2. If there was a loud bang or the door seemed heavy, leave the release and the door alone: a spring may have snapped.
  3. Arrange another way to get where you are going for now. The car can wait inside.
Call (289) 301-8323

Request a visit What the fix involves

Winter is hard on garage doors. Grease thickens, steel contracts, and a spring that was tired in October lets go in January. We service doors for the seasons they actually live through, with lubricants rated for the cold and hardware that shrugs off salt.

Request a visit

Same fees day or night · 19 years in business

The fix, explained · Toronto

What is the door doing?

EmergencyTorsion Spring ReplacementThe door starts to rise, gets about the height of your knee, then shudders and reverses.

The fix

The finished result is a door that behaves the way a good garage door should: it lifts by hand with light effort, stays where you leave it at mid-height, closes softly and lets the opener run with little strain. Reaching that point involves measuring the door, choosing a matched spring, winding it to the correct turns and…

Until then

  1. When a spring breaks, the safe approach for the household is to leave the door where it is, keep people and vehicles clear, and avoid running the opener, which can damage the top section, the trolley or the gear drive.

  2. Pull the manual release only when the door is fully closed unless a technician asks otherwise; a door disconnected while partly open can move on its own if the springs are out of balance.

Call (289) 301-8323Request a visit Torsion Spring Replacement

EmergencyOff-Track Garage Door ResetA delivery van backed into the shop's overhead door this afternoon.

The fix

The finish of an off-track reset matters as much as the re-seating. Once the rollers are home and the track is true, the door is disconnected from the opener and moved by hand through its whole travel while every roller is watched in its rail.

Until then

  1. Never run the opener on a door that is off its track or hanging crooked; every cycle drives the racked door harder into the rails and can pull the track from the wall or tear a hinge.

  2. Pull the manual release only when the door is fully closed unless a technician asks otherwise; a door disconnected while partly open can move on its own if the springs are out of balance.

Call (289) 301-8323Request a visit Off-Track Garage Door Reset

EmergencyGarage Door Cable ReplacementThere was a sharp crack from the garage, and when you went to look the door had dropped on one side and jammed.

The fix

Which counterbalance your door has shapes the job. Torsion doors carry a spring on a shaft above the opening, and the cables wind onto grooved drums at each end; the technician winds the spring down with steel bars, swaps the cables, sets the drums and winds it back up.

Until then

  1. Never run the opener on a door that is off its track or hanging crooked; every cycle drives the racked door harder into the rails and can pull the track from the wall or tear a hinge.

  2. Pull the manual release only when the door is fully closed unless a technician asks otherwise; a door disconnected while partly open can move on its own if the springs are out of balance.

Call (289) 301-8323Request a visit Garage Door Cable Replacement

EmergencyExtension Spring ReplacementYou pulled the red cord to open the door during a power cut and it barely moved.

The fix

What you have afterwards is a door that behaves like a much lighter object. Both corners leave the floor together, the door holds still when you stop it at waist height, and it settles onto the floor instead of slamming.

Until then

  1. When a spring breaks, the safe approach for the household is to leave the door where it is, keep people and vehicles clear, and avoid running the opener, which can damage the top section, the trolley or the gear drive.

  2. Pull the manual release only when the door is fully closed unless a technician asks otherwise; a door disconnected while partly open can move on its own if the springs are out of balance.

Call (289) 301-8323Request a visit Extension Spring Replacement

Book soonEmergency Release RepairSomeone pulled the cord last spring to get a car out during an outage, and the door has never properly rejoined the opener.

The fix

Beyond the repair, this service leaves every adult in the house able to use the release confidently. You see the handle pulled straight down with the door shut, the door lifted by its handle or a gripping point away from the panel joints, and the trolley clicked back together by pulling the cord toward the opener or running one…

Until then

  1. Pull the release with the door fully closed whenever possible, and keep the opening clear as you do.

  2. Lift a door by its handles or the gripping points on the panel face, never at the joint between sections, which closes as the door bends around the track.

Call (289) 301-8323Request a visit Emergency Release Repair

Book soonGarage Door Opener Diagnosis and RepairThe door goes up perfectly.

The fix

What you get from the visit is more than a working door. You get told, in plain words, what was wrong and why it happened: a gear that had run dry for years, a sensor knocked out of line by a snow shovel, a wall control left in lock mode by a visiting grandchild.

Until then

  1. Pull the release with the door fully closed whenever possible, and keep the opening clear as you do.

  2. Never drive a vehicle at a closed door to get out; the door collapses and the stored tension in the counterbalance is released.

Call (289) 301-8323Request a visit Garage Door Opener Diagnosis and Repair

Technician in a mesh cap and safety glasses holding a wrench to a bracket at the bend of the metal door track.
  • 19years in business
  • 24/7open, every day
  • Same feesday, night or weekend
  • On siteassessment preferred

Our way of working

Springs and cables are under a great deal of tension, and the proper way to handle them is well understood: the right winding bars, the door clamped, the tension released in steps. That care is simply how the job is done. It is also why our repairs hold and why the door runs true afterwards.

Malvern

  • Explained on the spot. As each part is checked, the technician tells you what it shows and what it means for the door as a whole.

  • Tidiness as standard. Old springs, cables and packaging leave with us, and the workspace is swept. A clean finish is part of every visit.

  • Options at your pace. Hear the choices, ask your questions, take the time you need. The work starts when you say so and not before.

Speak with us about the work: (289) 301-8323

Garage door services

Doors, openers and hardware

Think of this page as a map of the door. Start at the part that worries you, and follow it to the service page that describes the fix, the parts involved and how a door usually runs afterwards.

Four long coiled garage-door springs on a concrete floor, three black with metal end cones and one rusty spring broken in two.RepairsRepair & MaintenanceBetween a full replacement and doing nothing sits a lot of sensible work: resetting a door that has come off its rails, replacing a cracked section…Services
Gloved hands holding a metal roller wheel against a door track, with pliers and small hardware on a stepladder tray nearby.SpringsSprings & HardwareEvery spring has a fixed number of open and close cycles in it, and a busy household uses them up sooner than a quiet one.Services
Technician kneeling at a garage opening, pushing a black rubber seal into the metal jamb, with a red utility knife nearby.OpenersOpeners & AccessOpeners wear in predictable ways: gears strip, chains stretch, logic boards tire.Services
Technician on a blue stepladder using a wrench on a black torsion spring bar above a sectional door with small windows.New DoorsInstallation & UpgradesGlass garage doors turn a garage into a room: a gym, a studio, a covered patio that opens to the yard.Services

Sound familiar?

The largest moving part of your home. Worth a closer look.

Technician holding a black decorative strap hinge on a beige paneled garage door and driving a screw with a yellow drill.

1 / 3

The opener in the ceiling is older than the car parked under it. It groans on the way up, the light fixture rattles, and there are no small sensors near the floor. The last technician mentioned that parts for that model stopped being made years ago.

Garage Door Opener Replacement

Two gray-blue vertical-plank garage doors under a pebble-textured concrete overhang, half in shadow, beside a green shrub and a paved lot.

2 / 3

The motor runs, the chain rattles along the rail, and the door does not move a millimetre. You notice the little carriage sliding back and forth on its own. Last week the power was out and someone pulled the red cord to get the car out.

Garage Door Opener Diagnosis and Repair

3 / 3

The door came down fine but with a scraping noise, and now the vertical track on one side is bowed away from the wall. Two screws have pulled out of the wood and the roller nearest the floor has no rail around it.

Off-Track Garage Door Reset

Which fix fits?

IfThe manual lock bar no longer lines up with the slot in the track.

ThenManual lock realignment.

Doors shift over time; adjusting the bar or the track slot restores a lock that seats without forcing.

IfThe T-handle is loose and the key turns without engaging.

ThenLock handle and cylinder replacement.

Worn cylinders and handles are replaced as a set so the door is secure again.

IfThe manual lock is still fitted on a door that now has an opener.

ThenLock disable.

An engaged manual lock can stall the opener; it should be removed or fixed in the open position.

IfThe motor runs, the chain rattles along the rail, and the door does not move a millimetre.

ThenGarage Door Opener Diagnosis and Repair.

What you get from the visit is more than a working door.

IfThe rail shakes when the door runs.

ThenChain-Drive Opener Repair.

Here is how a visit runs.

IfThe door used to glide up with a soft hum.

ThenBelt-Drive Opener Repair.

A belt drive is chosen for its quiet, so one that has started to rattle is saying something specific.

Open 24/7 in Toronto

How a visit goes

Frenchman's Bay Garage Door Services

Job ticket · open 24/7

  1. 1 Call

    Speak with us about the work

    Describe the property, the hardware and what has changed, and the visit starts from what you have seen.

    (289) 301-8323 · open 24/7

  2. 2 Questions

    Your call, your words

    There is no wrong way to describe a garage door problem. Tell us what you saw and heard; we ask the follow-up questions.

  3. 3 On the way

    In the van

    Toronto to Malvern.

    • Torsion springs, oil-tempered or galvanized
    • Wire gauge and tape measure
    • Winding bars
    • Cable drums
    • Stationary cone bolts and nuts
  4. 4 Fixed

    Putting it right

    Finding the real cause. A door that stops halfway can be a sensor, a spring or a stripped gear. We test each possibility rather than assuming the obvious one.

    Putting it right. The technician fits the correct parts, adjusts the opener to the door, and shows you the result running through full cycles.

Same fees day, night or weekend · on-site assessment preferred

Toronto, Ontario

Toronto information

Town
Toronto, Ontario
In business
19 years
Hours
Open 24/7 · nights, weekends and holidays, same fees
Visits
On-site assessment preferred. Request a visit or call.

What the census means at the door

58%

Older homes. About 58% of homes in Toronto were built in 1980 or earlier, according to the 2021 Census.

Wood door frames in an older house settle and swell over the decades, which can leave a door rubbing on one side. Rather than forcing the opener, the technician trues the tracks, adjusts the jamb seals and sets the door so it travels freely again.

23%

Single-detached houses make up about 23% of homes in Toronto (2021 Census).

Where most homes are townhouses, condos or apartments, garage doors are often shared: a single overhead door or gate serving an underground or common garage. Those doors run on commercial operators built for constant use, and their upkeep is usually arranged through the building's management.

Source: Statistics Canada, 2021 Census of Population

Nearby

Open Toronto in Google Maps

Asked and answered

Advice · (289) 301-8323

Should I lubricate the tracks?

No. Tracks should be clean and dry. Rollers are meant to roll along the track on their own bearings, and a film of lubricant on the track collects grit, thickens in the cold and makes the rollers slide and drag instead. Wipe the tracks with a rag and put the lubricant where it belongs: on the hinge pins, the roller bearings, the spring coils and the bearing plates at the ends of the torsion shaft.

Does road salt harm the door?

Salt carried in on tires and shovelled snow settles on the lowest hardware: the bottom brackets, the lower track, the bottom roller stems and fixture bolts. Those are the parts that carry the door's weight, so corrosion there matters. Rinsing the lower hardware and the inside face of the bottom section after winter, keeping the floor by the tracks swept, and having the bottom brackets looked at each spring keeps salt from becoming a structural problem.

How should I prepare the garage before the visit?

Move vehicles out of the garage or well clear of the door's path, and clear the floor under the opening and along both tracks so a stepladder can be set up. Keep children and pets out of the garage during the work. If you have the door or opener manual, or know the model, have it handy. A short note of what you have noticed and when, especially in cold weather, is genuinely useful.

Can extension springs be converted to a torsion system?

In many garages, yes. A conversion adds a shaft, centre and end bearings, drums and torsion springs above the opening and removes the extension springs and pulleys from beside the tracks. It needs enough headroom above the door for the shaft and solid framing for the centre bracket. The technician measures the space and the door before recommending it, and the result is smoother, more even lifting with hardware kept clear of the sides.

Open 24/7

Request a visit

Ask for a quote

Call now · open 24/7(289) 301-8323
  • On-site assessment preferred
  • Same fees day, night or weekend
  • 19 years in business